ARDUINO

The LCD Keypad shield is developed for Arduino compatible boards, to provide a user-friendly interface that allows users to go through the menu, make selections etc. It consists of a 1602 white character blue backlight LCD. The keypad consists of 5 keys — select, up, right, down, left and reset. To save the digital IO pins, the keypad interface uses only one ADC channel. The key value is read through a 5 stage voltage divider.

Specifications:

• Operating Voltage: 5V
• Push buttons: 6 

Additional Information:

• Item Code: BE60047
• Minimum Order Quantity: 1 Piece

• he Arduino Uno Rev3 is a micro controller board based on the ATmega328 (datasheet).
• It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs.
• It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started
• The Uno differs from all preceding boards in that it does not use the FTDI USB-to-serial driver chip. Instead, it features the Atmega8U2 programmed as a USB-to-serial converter.

Additional Information:

• Minimum Order Quantity: 1 Piece

ATMega2560 Development Board with CH340 USB

The ATMega 2560 is functionally identical to the extremely popular and easy-to-use open source Arduino Mega.
The board is based on the ATmega2560 wich runs at 16MHz. It has 54 digital I/O pins (of which 15 provide PWM output) and 16 analog inputs.

Specifications:

• Microcontroller: ATmega2560
• Clock Speed: 16 MHz
• Operating Voltage: 5V
• Input Voltage (recommended): 5.5-9V
• Digital I/O Pins: 54 (of which 15 provide PWM output)
• Analog Input Pins: 16
• Flash Memory: 256KB (of which 8KB used by bootloader)
• SRAM: 8 KB
• EEPROM: 4 KB Does not comes with a USB Cable, which can be purchased separately

Additional Information:

• Item Code: BE60121
• Minimum Order Quantity: 1 Piece
• Port of Dispatch: COIMBATORE

Description: This is the newest revision of our FTDI Basic. We now use a SMD 6-pin header on the bottom, which makes it smaller and more compact. Functionality has remained the same. This is a basic breakout board for the FTDI FT232RL USB to serial IC. The pinout of this board matches the FTDI cable to work with official Arduino and cloned 5V Arduino boards. It can also be used for general serial applications. The major difference with this board is that it brings out the DTR pin as opposed to the RTS pin of the FTDI cable. The DTR pin allows an Arduino target to auto-reset when a new Sketch is downloaded. This is a really nice feature to have and allows a sketch to be downloaded without having to hit the reset button. This board will auto reset any Arduino board that has the reset pin brought out to a 6-pin connector. The pins labeled BLK and GRN correspond to the colored wires on the FTDI cable. The black wire on the FTDI cable is GND, green is CTS. Use these BLK and GRN pins to align the FTDI basic board with your Arduino target. This board has TX and RX LEDs that make it a bit better to use over the FTDI cable. You can actually see serial traffic on the LEDs to verify if the board is working. This board was designed to decrease the cost of Arduino development and increase ease of use (the auto-reset feature rocks!). Our Arduino Pro boards and LilyPads use this type of connector. One of the nice features of this board is a jumper on the back of the board that allows the board to be configured to either 3.3V or 5V (both power output and IO level). This board ship default to 5V, but you can cut the default trace and add a solder jumper if you need to switch to 3.3V. Note: We know a lot of you prefer microUSB over miniUSB. Never fear, we’ve got you covered! Check out our FT231X Breakout for your micro FTDI needs!

Additional Information:

• Item Code: BE70051
• Minimum Order Quantity: 1 Piece
• Port of Dispatch: COIMBATORE

A Controller Area Network (CAN bus) is a robust vehicle bus standard designed to allow microcontrollers and devices to communicate with each other's applications without a host computer. It is a message-based protocol, designed originally for multiplex electrical wiring within automobiles to save on copper, but it can also be used in many other contexts. For each device, the data in a frame is transmitted sequentially but in such a way that if more than one device transmits at the same time, the highest priority device can continue while the others back off. Frames are received by all devices, including by the transmitting device.

Technical data:
Microcontroller: ATmega2560
Operating voltage: 5 V
Input voltage (recommended): 7 - 12 V
Input voltage (maximum): 6 - 20 V
Digital I/O pins: 54 (of which 14 can be used for PWM output)
Analogue input pins: 16
Direct current at each I/O pin: 40 mA
Direct current at 3.3-V pin: 50 mA
Flash memory: 256 KB, 8 KB of which is used by the bootloader
SRAM: 8 KB
EEPROM: 4 KB
Clock speed: 16 MHz

Product Details:

The Arduino Uno SMD is a version of the Arduino Uno, but uses an surface mount version of the Atmega328P instead of the through-hole version. This version was made in response to a shortage in supply of the through-hole Atmega328P. The board is based on the ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started.

The Uno differs from all preceding boards in that it does not use the FTDI USB-to-serial driver chip. Instead, it features the Atmega8U2 programmed as a USB-to-serial converter.

"Uno" means one in Italian and is named to mark the upcoming release of Arduino 1.0. The Uno and version 1.0 will be the reference versions of Arduino, moving forward. The Uno is the latest in a series of USB Arduino boards, and the reference model for the Arduino platform; for a comparison with previous versions, see the index of Arduino boards.

Product Details:

QUICK OVERVIEW

1. Operating Voltage(V): 3- 5
2. Operating Current(mA): 2
3. Communication protocol: I2C
4. Power saving mode
5. Automotive grad
6. Small size, low cost

The MLX90614ESF is an Infra-Red thermometer for non-contact temperature measurements.  Both the IR sensitive thermopile detector chip and the signal conditioning ASIC are integrated in the same TO-39 can. Integrated MLX90614 is a low noise amplifier, 17-bit ADC and powerful DSP unit thus achieving high accuracy and resolution of the thermometer.

The user can configure the digital output to be PWM. As a standard, the 10-bit PWM is configured to continuously transmit the measured temperature in the range of -20 to 120 °C, with an output resolution of 0.14 °C.

Application:

1. High precision non-contact temperature measurements
2. Thermal Comfort sensor for Mobile Air Conditioning control system
3. The temperature sensing element for residential, commercial and industrial building air conditioning Windshield defogging
4. The automotive blind angle detection
5. Industrial temperature control of moving parts
6. Temperature control in printers and copiers
7. Home appliances with temperature control
8. Healthcare
9. Livestock monitoring
10. Movement detection
11. Multiple zone temperature control – up to 127sensors can be read via common 2 wires
12. Thermal relay/alert
13. Body temperature measurement

Features:

1. Works from 3.3V to 5V input, Module has power regulator IC built-in.
2. Standard I2C interface with built 2x pull up resistors
3. When measuring the temperature, please maintain a measuring distance of 1 cm
4. Small size, low cost
5. Easy to integrate
6. Factory calibrated in a wide temperature range: -40 to 125 °C for sensor temperature and -70 to 380 °C for object temperature.
7. High accuracy of 0.5°C over the wide temperature range (0..+50 C for both Ta and To)
8. Medical accuracy of 0.1°C in a limited temperature range available on request
9. The measurement resolution of 0.01°C
10. SMBus compatible digital interface for fast temperature readings and building sensor networks
11. Customizable PWM output for continuous reading
12. Simple adaptation for 8 to 16V applications

Package Includes:

1 x MLX90614ESF Non-Contact Human Body Infrared Temperature Measurement Module

Additional Information:

• Delivery Time: 2 days

Features:

100% Arduino-compatible Board.

ATmega328P running at 8MHz with external resonator (0.5% tolerance)

Supports auto-reset.

Max Output Current: 150mA

Over current protected

Reverse polarity protected

DC input: 5V up to 12V

On board Power and Status LEDs

Size: 33mm x 18 mm x 6mm

Additional Information:

• Minimum Order Quantity: 1 Piece
• Delivery Time: 2 days

11 digital input/output pins, all pins have interrupt/pwm/I2C/one-wire supported(except D0)
1 analog input(3.3V max input)
A Micro USB connection
A power jack, 9-24V power input.
Compatible with Arduino
Compatible with nodemcu

Additional Information:

• Item Code: BE60205
• Minimum Order Quantity: 1 Piece

Product Details:

Arduino Pro Mini ATmega328The Arduino Pro Mini is intended for advanced users who require flexibility, low-cost, and small size. It comes with the minimum of components (no on-board USB or pin headers) to keep the cost down. Be sure to provide the correct power and use components whose operating voltage matches that of the board.
The board comes without built-in USB circuitry, so an off-board USB-to-TTL serial convertor must be used to upload sketches. This can be a FTDI TTL-232R USB - TTL Level Serial Converter Cable for the 5V Arduino Mini Pro), or a FTDI TTL-232R-3V3 USB - TTL Level Serial Converter Cable. One quick way to connect these is by inserting a six-pin 0.1" male pin header into the end of the FTDI cable or breakout board, and pressing it against the six hole programming header on the Mini Pro. If, however, you''re going to be uploading lots of sketches to your Pro Mini, you''ll probably want to solder some pins (male headers) to the holes.
The board can be powered through USB via the six-pin programming header, or from a regulated 5V (depending on the model) supply applied to the VCC pin or an unregulated supply on the RAW pin.
Any standard 0.1" spaced header can be soldered to the holes on the Arduino Pro Mini. To use every pin requires two 12-pin headers, plus a six pin header for programming, if desired. Bare wire can also be soldered directly to the holes.

ATMEGA 328 Specifications : 

• 131 Powerful Instructions – Most Single Clock Cycle Execution
• Up to 20 MIPS Throughput at 20 MHz
• Two 8-bit Timer/Counters with Separate Prescaler and Compare Mode
• One 16-bit Timer/Counter with Separate Prescaler, Compare Mode, and Capture Mode
• Real Time Counter with Separate Oscillator
• Six PWM Channels
• 8-channel 10-bit ADC in TQFP and QFN/MLF package
• Programmable Watchdog Timer with Separate On-chip Oscillator
• On-chip Analog Comparator
• 23 Programmable I/O Lines

Specification:

• ATmega328
• Operating Voltage (logic level) 5 V
• Digital I/O Pins 14 (of which 6 provide PWM output)
• Input Voltage (recommended) 7-12 V
• DC Current per I/O Pin 40 mA

Additional Information:

• Item Code: BE60160

1. Microcontroller: ATmega168 or ATmega328V
2. Operating Voltage: 2.7-5.5 V
3. Digital I/O Pins: 14
4. PWM Channels: 6
5. Analog Input Channels: 6
6. DC Current per I/O Pin: 40 mA
7. Board will run from 2V to 5V.
8. The latest version of the LilyPad supports automatic reset for even easier programming.
9. The back side of the LilyPad is now completely flat!

The LilyPad 328 ATmega328P Main Board 16M is a compatible Arduino-program micro-controller designed to be easily integrated into e-textiles and wearable projects. It offers the same functionality you find in other Arduino boards, in a lightweight, round package design to minimize snagging and profile. With wide tabs that can be sewn down and connect with conductive thread.

The LilyPad consists of an ATmega328 compatible with the Arduino bootloader and a minimum number of external components to keep it as small (and as simple) as possible.

This board will run from 2V to 5V and offers large pin-out holes that make it easy to sew and connect. Each of these pins, with the exception of (+) and (-), can control an attached input or output device (like a light, motor, or switch).

Each LilyPad was creatively designed to have large connecting pads to allow them to be sewn into clothing. Various input, output, power, and sensor boards are available. They’re even washable! 

Features :

1. Board will run from 2V to 5V.
2. The latest version of the LilyPad supports automatic reset for even easier programming.
3. The back side of the LilyPad is now completely flat!
4. We now use a surface mount programming connector to keep the header from poking through.
5. This version of the LilyPad now uses the new ATmega328 at 8MHz.
6. Arduino 0016 supports the Pro Mini Arduino 328/8MHz/16MHZ.
7. Use this setting when using this new LilyPad 328.

Package Includes :

1 x LilyPad 328 ATmega328P Main Board 16M

Additional Information:

• Minimum Order Quantity: 1 Piece

• 
  4 x 4 Matrix Membrane Keypad 8 pin connector Adhesive mounting Maximum Circuit Rating: 35VDC, 100mA Insulation Resistance: 100M Omh, 100V Dielectric Withstand: 250VRms (50-60Hz, 1min) Life Expectancy: 1 million closures Operation Temperature: 0 to +70 centigrade Pad Size (L x W): Approx. 3 x 2.7 inch / 76 x 69 mm Fexible Circuit Length: Approx. 3.3 inch / 83 mm

Additional Information:

• Minimum Order Quantity: 1 Piece

It is a great kit to new Arduino users and geeks who have sparkling ideas. You can choose to do soldering in the soldering area. You can also make good use of the mini breadboard which can save your time of soldering, to try any circuit you want to the Arduino. You also can choose to use your own breadboard.

Arduino Protoytpe Shield Specifications:-
1.It has a nice standard 0.1" x 0.1" prototying grid with big pads.
2.A IC pattern for adding DIP ICs up to 20 pins
3.Power rails down the middle and sides
4.A reset button and an extra general use button
5.Two general use 3mm LEDs, as well as 2 matching resistors
6.The ICSP header is up top if you like to upload to your Arduino using a programmer
7.A surface-mount chip area for up to 14 SOIC size parts Compatible with either tiny breadboards or ''standard''
breadboards with the rails removed.
8.Every pin is brought out, including the new 3V and Reset header pins
9.Two 0.1uF capacitors on either side for extra power stability. (Purchase Separately)

Additional Information:

• Minimum Order Quantity: 1 Piece(s)
• Port of Dispatch: COIMBATORE
• Delivery Time: ready stock
• Packaging Details: ESD cover

• Power supply voltage: 2.7 V-3.3 V/5 V
• Data interface level: 2.7-5V.
• Resolution: 84 x 48 pixel
• Backlight power supply voltage: highest 3.3 V.
• Backlight: Blue

Additional Information:

• Item Code: BE50018
• Minimum Order Quantity: 1 Piece

• Support Micro SD Card (<=2G), Micro SDHC card (<=32G) (high-speed card)
• The level conversion circuit board that can interface level is 5V or 3.3V
• Power supply is 4.5V ~ 5.5V, 3.3V voltage regulator circuit board
• Communication interface is a standard SPI interface
• 4 M2 screw positioning holes for easy installation
• Size: 4.1 x 2.4cm

Additional Information:

• Item Code: BE50019
• Minimum Order Quantity: 1 Piece

• 1Hz output pin SQW.
• 32KHz output pin 32K.
• Voltage Supply: 2.2 V ~ 5.5 V (for RTC).
• Time Format: HH: MM: SS (12/24 hr).
• Date Format: YY-MM-DD-dd.
• DS3231 based RTC with 2032 Battery Holder.
• Highly Accurate RTC
• Real-Time Clock Counts
• Digital Temp Sensor Output.
• Register for Aging Trim.
• Two Time-of-Day Alarms.
• Programmable Square-Wave Output Signal.
• Configurable I2C device Address for AT24C32 using SMD jumpers on PCB (A0, A1, A2)

Additional Information:

• Item Code: BE50020
• Minimum Order Quantity: 1 Piece

• Skip the wiring and start playing in 30 seconds
• Slim and slick board design
• Support Arduino UNO and Arduino Mega2560 and other development board Arduino DUE line, without any wiring.
• Arduino libraries provide.
• This board also supports STM32, C51 and other conventional MCU, provide development code.
• Control IC: ILI9481
• Interface: 8bit parallel
• NO Touch screen
• resolution 320×480

Additional Information:

• Item Code: BE50015
• Minimum Order Quantity: 1 Piece

CH340G Serial Converter USB 2.0 to TTL 6PIN Module, Newest version for Pro Mini interfaceDescription :-*Built-in USB to TTL Transfer chip.*can be used for USB to TTL electronic projects.*TTL interface output, easy to connect to your MCU.*Status LEDDual 3.3V and 5V Power output, work with 3.3v and 5v target device.

Additional Information:

• Item Code: BE60129
• Minimum Order Quantity: 1 Piece(s)
• Port of Dispatch: COIMBATORE

Description: Our friends over at LinkSprite have made this nifty little RS485 Shield, now you will be able to have a communication port for your field bus directly connected to your Arduino! Even though the RS485 is sometimes thought as an archaic protocol, it will allow up to 32 devices to communicate through the same data line over a cable length of up to 4000ft with a maximum data rate of 10Mbit/s. Those arent bad numbers!This version of the RS485 shield removes the optional DB9 connector bay and adds a second 2-pin screw terminal and the ability to choose two pins from your Arduinos D0 to D7 as Software Serial Ports to communicate with the shield.This shield does come without its headers separate so a small amount of soldering will be required before attaching it to your Arduino device.

Additional Information:

• Minimum Order Quantity: 1 Piece
• Port of Dispatch: COIMBATORE

Product Details:

Product Details:

This is a I/O extension shield for Arduino Nano making connection easier.
Features: • Expansion shield for Arduino Nano• Pin out for 14 digital input/output pins• Pin out for 6 PWM outputs• Pin out for 8 analog inputs• Pin out for I2C Interface• Power jack• Reset button• LED for power indicator• AMS1117 3.3V Output Voltage• Also compatible with Arduino UNO after soldering pin headers to this shield
Size:2.3" x 2.2" x 0.5"

Additional Information:

• Delivery Time: 2 days

We are one of the prominent manufacturers, suppliers and retailers, service provider of a vast range of Embedded Development Boards, Electronic Counters, Self Learning Kit & many more and service providers of Electronic Project Services.

Additional Information:

• Item Code: BE60100
• Minimum Order Quantity: 1 Piece