Electronic Components

Specifications:

MINI  ARM BOARD LPC2418 .
All pin outs are taken out with burg connector .

Additional Information:

• Item Code: BE30044
• Minimum Order Quantity: 1 Piece

The ATMEGA328P-PU is a low-power CMOS 8-bit microcontroller based on the AVR enhanced RISC architecture. By executing powerful instructions in a single clock cycle, the ATmega328P-PU achieves throughputs approaching 1 MIPS per MHz allowing the system designer to optimize power consumption versus processing speed.
                The AVR core combines a rich instruction set with 32 general purpose working registers. All the 32 registers are directly connected to the Arithmetic Logic Unit (ALU),allowing two independent registers to be accessed in one single instruction executed in one clock cycle. The resulting architecture is more code efficient while achieving throughputs up to ten times faster than conventional CISC microcontrollers.
                        
The ATmega328P-PU AVR is supported with a full suite of program and system development tools including: C Compilers, Macro Assemblers, Program Debugger/Simulators, In-Circuit Emulators, and Evaluation kits.
Features :

High Performance, Low Power Design

8-Bit Microcontroller Atmel® AVR® advanced RISC architecture

131 Instructions most of which are executed in a single clock cycle

Up to 20 MIPS throughput at 20 MHz

32 x 8 working registers

2 cycle multiplier

Memory Includes

32KB of of programmable FLASH

1KB of EEPROM

2KB SRAM

10,000 Write and Erase Cycles for Flash and 100,000 for EEPROM

Data retention for 20 years at 85°C and 100 years at 25°C

Optional boot loader with lock bits

In System Programming (ISP) by via boot loader

True Read-While-Write operation

Programming lock available for software security

I/O and Package

23 programmable I/O lines

28 pin PDIP package

Operating voltage:1.8 - 5.5V

Operating temperature range:40°C to 85°C

Speed Grades:

0-4 MHz at 1.8-5.5V

0-10 MHz at 2.7-5.5V

0-20 MHz at 4.5-5.5V

Low power consumption mode at 1.8V, 1 MHz and 25°C:

Active Mode: 0.3 mA

Power-down Mode: 0.1 μA

Power-save Mode: 0.8 μA (Including 32 kHz RTC)

Package:  Lead Free PDIP 28

Package includes:

1 x ATMEGA328P-PU Microcontroller(PDIP)

Additional Information:

• Minimum Order Quantity: 1 Piece
• Delivery Time: 2 DAYS

Product Details:

1. Model: MG995
2. Weight: 55 gm
3. Operating voltage: 4.8V~ 7.2V
4. Servo Plug: JR
5. Stall torque @4.8V : 10 kg-cm
6. Stall torque @6.6V : 12 kg-cm

Additional Information:

• Item Code: BE90015

We are one of the prominent manufacturers, suppliers and retailers, service provider of a vast range of Embedded Development Boards, Electronic Counters, Self Learning Kit & many more and service providers of Electronic Project Services.

Additional Information:

• Item Code: BE60093
• Minimum Order Quantity: 1 Piece

Product Details:

This display overcomes the drawback of LCD1602 Parallel LCD Display in which you’ll waste about 8 Pins on your Arduino for the display to get working. Luckily in this product, an I2C adapter is directly soldered right onto the pins of the display. So all you need to connect are the I2C pins, which shows a good library and little of coding.

The I2C is a type of serial bus developed by Philips, which uses two bidirectional lines, called SDA (Serial Data Line) and SCL (Serial Clock Line). Both must be connected via pulled-up resistors. The usage voltages are standard as 5V and 3.3V.

If you already have the I2C adapter soldered onto the board like in this product, the wiring is quite easy. You should usually have only four pins to hook up. VCC and GND of course. The LCD display works with 5 Volts. So we go for the 5V Pin.

The values shown on the display can be either a simple text or numerical values read by the sensors, such as temperature or pressure, or even the number of cycles that the Arduino is performing.

If you are having an I2C adapter and only want to buy display then click below,

LCD1602 Parallel LCD Display

For more displays click below,

LED/LCD Display

Features :

1. Arduino IIC/I2C interface was developed to reduce the IO port usage on Arduino board
2. I2C adapter allows flexibility in connections
3. I2C Reduces the overall wirings.
4. 16 characters wide, 2 rows
5. White text on the Blue background
6. Single LED backlight included can be dimmed easily with a resistor or PWM.

QUICK OVERVIEW

1. Model: LCD1602
2. Interface: I2C
3. Interface Address: 0x27
4. Character Color: White
5. Backlight: Blue
6. Supply voltage: 5V
7. Dimensions: 80 x 36 x 18 (LxWxH) mm.

Product Details:

We are one of the prominent manufacturers, suppliers and retailers, service provider of a vast range of Embedded Development Boards, Electronic Counters, Self Learning Kit & many more and service providers of Electronic Project Services.

Additional Information:

• Item Code: BE30160

Product Details:

Easy to Use:- simply insert the glue stick into the hole at the back of the glue gun,slide it in until it stops by pull the trigger. Turn on the power, preheating the hot glue gun for about 1-3 minutes to soften the glue stick. Once it s been sufficiently melted, pull the trigger, the glue will ooze out. Suitable For - 11mm Glue Sticks, bonding the toy model, artificial flowers, Christmas trees, ornaments, metal products, wood products, cardboard, electronic circuit boards.

• Operating Power: 40 W
• Feed Type: Trigger-fed Gun
• Gun Stand Included
• 11 MM GLUE STICKS

Additional Information:

• Delivery Time: 2 days

Working Voltage: 3.3V-5V DC

Working Current: >1A

Detection Distance: 2~60cm

Detection Angle: 35°
Size:
Big Board: 42*38*12mm
Small Board: 25*12*12mm

Mounting Hole Diameter: 3mm

 

Note:
1, Do not put probe toward sunlight. Sunlight will cause interference to module.
2, Sensitivity should not be regulated excessively high because high sensitivity can easily lead to false trigger.

 

Package Includes:

1 x Infrared Tracking Module Set

Additional Information:

• Item Code: BE90014
• Minimum Order Quantity: 1 Piece

We are one of the prominent manufacturers, suppliers and retailers, service provider of a vast range of Embedded Development Boards, Electronic Counters, Self Learning Kit & many more and service providers of Electronic Project Services.

Additional Information:

• Minimum Order Quantity: 1 Piece
• Delivery Time: 2 days

Product Details:

We are one of the prominent manufacturers, suppliers and retailers, service provider of a vast range of Embedded Development Boards, Electronic Counters, Self Learning Kit & many more and service providers of Electronic Project Services.

Product Details:

We offer solenoid Valve for water application

Technical specification :

• Solenoid Valve body - Metal Brass
• Operating Voltage 230 Volts AC
• Pipe size 1/2 inches
• Pressure : 0 - 7 Kg/cm2
• Orifice : 16mm
• Operating temp : -5deg C to 80Deg C

Product Details:

1. Quad-band 850/900/1800/1900MHz.
2. GPRS class 2/10.
3. Input Voltage : 9V-12V DC.
4. Control via AT commands (3GPP TS 27.007, 27.005 and SIMCOM enhanced AT command set).
5. Configurable baud rate.
6. Built-in SIM Card holder.
7. Built-in Network Status LED

 With this board you can develop and prototype with any of 8051 40 pin microcontrollers RTC based Clock, DS1307 is Dallas RTC Chip I2C based. The board have User button and status LED. The bridge rectifire allow this board to be powered with both AC and DC power supply adapters.

Features

•    DIL40 microcontroller socket.
•    Quartz crystal 11.0592 MHz.
•    DIL8 RTC Socket.
•    Buzzer for Alarm.
•    PBT Switches for Inputs.
•    Reset button.
•    Power plug-in jack.(Ac/Dc 12V)
•    LCD Display Interface.
•    GND bus.
•    VDD bus.
•    Four mounting holes 3,3 mm (0,13").

Soldering Iron is a hand tool used in soldering. We deal with Soldering iron by Soldron which supplies heat to melt the solder so that it flows through the joint between two pieces. These irons find a low usage in plastic welding and pyrography and are mainly used for installation, repairs and production work in electronic applications. This is the most popular product as it is general purpose for all electrical applications. We offer this iron at market leading prices to our customers.

Specifications:

Dimensions: 460x320x320 mm

Input Voltage: 220 V

Output Power: 30 W

Additional Information:

• Item Code: BE20119
• Minimum Order Quantity: 1 Piece

Product Details:

We deal with AC indication lamp for panel boards .

Operating voltage : 230 volts.
Colour : RED/YELLOW/GREEN

Additional Information:

• Item Code: BE20229

Digital multimeter

Specification :-

Measurement parameter.

1.DC Voltage
2.AC volatge
3.DC current
4.Resistance
5.Diode
6.Buzzer
7.Transistor HFE

Additional Information:

• Item Code: BE20260
• Minimum Order Quantity: 1 Piece

Product Details:

proximity sensor pnp-no
idf1-3008pa

We are one of the prominent manufacturers, suppliers and retailers, service provider of a vast range of Embedded Development Boards, Electronic Counters, Self Learning Kit & many more and service providers of Electronic Project Services.

Product Details:

The meter is a handheld digital multimeter for measuring DC and AC voltage, DC current, resistance, diode, and transistor with battery operated.
Precautions:
Always make sure the Test Probes are fitted in the correct sockets. (Specially while measuring AC Voltage)Please choose the correct measuring option BEFORE you connect the probe. (As a thumb rule always choose the greater value and decrease if required)While measuring Current, make sure to put the Red Probe in 10A socket and the measuring connection should be in SeriesWhile measuring all other parameters other than Current (Ampere ) , the measuring connection should be in ParallelIf by mistake a wrong connection or option is selected and the measurement is initiated, the instrument will Blink / Beep. REMOVE the connections IMMEDIATELY to restrict the damage to a minimum.Features:Safety Class: I CAT II 600V.Over-range indication: 1.Polarity display for negative polarity.Low voltage indication on the display.Data hold.Display Backlight.Fuse: F1: F250mA or 250V,F2: F 10A or 250V.Low Battery Display.

Infrared IR Sensor Receiver Module for Arduino adopts 1838 infrared receiving head. Light resistance, strong electromagnetic interference, built-in infrared dedicated IC, can work under 500 lux light intensity.

Widely used in stereo, TV, video machine, disc machine, set-top boxes, digital photo frame; car stereo, remote control toys, satellite receivers, hard disk player, air conditioner, heater; electric fan, lighting and other home appliances.

IR Receiver Module is a 38KHz infrared receiver module which is Arduino compatible. It can receive the standard 38KHz modulated remote controller signal. Through programming the Arduino, you can realize decoding of the remote controller signal. Using this item, you can make a universal remote controller with the learning function.

Product Details:

PIC Datasheet Microchip 16F877A

Specifications:

• Operating Temperature: 40°C-85°C
• Supply Voltage: 4 V-5.5 V

Additional Information:

• Item Code: BE20066

Rocker Switch - SPST (round)

Description: This little round on/off toggle switch is rated up to 10A at 125VAC and can be panel
mounted in a 20mm diameter hole. It'll also look pretty slick in your project

Additional Information:

• Item Code: BE70007
• Minimum Order Quantity: 1 Piece

• Angle Displacement Measurement
• Bends and Flexes physically with motion device
• Possible Uses.: Robotics, Gaming (Virtual Motion), Computer Peripherals.
• Simple Construction
• Flat Resistance: 25K Ohms
• Resistance Tolerance: ±30%
• Bend Resistance Range: 45K to 125K Ohms
• Power Rating : 0.50 Watts continuous. 1 Watt Peak
• Temperature Range: -35°C to +80°C

Additional Information:

• Item Code: BE90017
• Minimum Order Quantity: 1 Piece

Product Details:

piezo electric buzzer

Additional Information:

• Production Capacity: 1000

Digital voltmeter 25v

Additional Information:

• Minimum Order Quantity: 1 Piece
• Delivery Time: 3 WORKING DAYS UPONTHE RECEIPT

Product Details:

We are one of the prominent manufacturers, suppliers and retailers, service provider of a vast range of Embedded Development Boards, Electronic Counters, Self Learning Kit & many more and service providers of Electronic Project Services.

Product Details:

We are one of the prominent manufacturers, suppliers and retailers, service provider of a vast range of Embedded Development Boards, Electronic Counters, Self Learning Kit & many more and service providers of Electronic Project Services.

• The device also can be used as a signal generator for electric speed controller (ESC)
• There are 3 modes to check servos or ESC
• It can connect 1-3 servos simultaneously and test such as 1-3 servos consistency and so on.
• It can also connect 1-3 ESC to test and compare their reaction time respectively.
• It can connect 3 servos of the CCPM helicopters and select servos

1. Model: DC 24V 10mm 5N
2. Rated Operating Voltage (VDC): 24
3. Operation Mode: Push-Pull (Normally Closed)
4. Holding Force (N): 5
5. Weight:33 gm

DC 24V Push-Pull Solenoid electromagnet, 10mm 5N  Push-Pull Type, open frame type, linear motion, plunger spring return, open coil form, DC electron magnet. Used widely in home appliances, vending machines, a game machine, auto door locks.

This DC 24V 10mm 5N Push-Pull Solenoid Electromagnet can be used for locking sell-machine, storage shelf, file cabinet and etc. The hidden way of unlocking can be used for an emergency. The lock works as the circuits disconnects, and it will unlock as the instant power-on.

It is steady, durable and energy-saving, and had a long lifespan. In the anti-theft and shockproof design, the lock is better than other kinds of locks. After connecting the wires and when the current is available, the electric lock can control the door’s opening and closing.

Note: Take care of polarity while making the connection without a connector.

Features:

1. Iron Body Material
2. High-quality ultra-compact electric lock.
3. Rustproof, durable, safe, convenient to use.
4. Suction tightly sucks the iron, thus locking the door.
5. Designed with the open frame type and mount board, high power.
6. Easy to install for the electric door lock or other automatic door lock systems with the mounting board
7. Applicable for being installed in the escape door or fire door electronic controlled system.
8. Adopts the principle of electric magnetism, when the current through the silicon, the electromagnetic lock will achieve a strong.

Product Details:

Features:

• Gear Type: All Metal Gears
• Operating Speed: 0.17sec / 60 degrees (4.8V no load)
• Operating Speed: 0.13sec / 60 degrees (6.0V no load)
• Stall torque: 12kg/cm(6V)
• Operation Voltage : 4.8 - 7.2 V
• Temperature range: 0℃ to 55℃
• Power Supply: Through External Adapter
• Stable and Shock Proof - Metal Gear - Double Ball Bearing
• Connector Wire Length 300mm
• Compliant with most standard receiver connector: Futaba, Hitec, Sanwa, GWS etc...
• Great for truck, Boat, Racing Car, Helicopter and Air-plane

Specifications:

• Connector wire length: ~300 mm
• Dimension: ~54 x 38 x 20 mm
• Net weight: ~61 g
• Package weight: ~71 g
• Color: Black

This is a high quality plastic worm gear. Use it to get the desired speed and torque from your motor. Worm gears are along with pinion or spur gears to change the rotational plane by 90 degrees. It comes with a 6mm bore and a set screw which makes it easy to attach the gear to motors and axles of various diameters. Perfect for use in science projects, robotics, etc
The outer diameter of this gear is 19 mm. It has a central hole/bore of diameter 6 mm. Fits perfectly with all our 6 mm axles and motors with 6mm shaft.
Features
Outer Diameter: 19mmGear Mod: Mod 1.6Inner Bore: 6mm, comes with set screw to securely attach the gear to the shaftApplication: Perfect for use in science projects, robotics, etc

Specifications:

• Operating Temperature: 40^oc-125^oc
• Supply Voltage: 1.5 v-6 v
• Dissipation Power: 1 w-6 w

Additional Information:

• Item Code: BE30051
• Minimum Order Quantity: 1 Piece

PCA9685 16 Channel 12 BIT PWM Servo Motor Driver has following features

• 2-bit resolution for each output – for servos, that means about 4us resolution at 60hz update rate.
• t’s an i2c-controlled PWM driver with a built in clock. That means that, unlike the TLC5940 family, you do not need to continuously send it signal tying up your microcontroller, its completely free running!
• It is 5V compliant, which means you can control it from a 3.3V microcontroller and still safely drive up to 6V outputs (this is good for when you want to control white or blue LEDs with 3.4+ forward voltages)
• 6 address select pins so you can wire up to 62 of these on a single i2c bus, a total of 992 outputs – that’s a lot of servos or LEDs
• Adjustable frequency PWM up to about 1.6 KHz

Additional Information:

• Item Code: BE90016
• Minimum Order Quantity: 1 Piece

Product Details:

This DC 12V Cabinet Door Lock Electric Lock Assembly Solenoid can be used for locking sell-machine, storage shelf, file cabinet and etc. The hidden way of unlocking can be used for an emergency. The lock works as the circuits disconnects, and it will unlock as the instant power-on. It is steady, durable and energy-saving and had a long lifespan. In the anti-theft and shockproof design, the lock is better than other kinds of locks. After connecting the wires and when the current is available, the electric lock can control the door’s opening and closing.

Note: Take care of polarity while making the connection without connector (i.e. Red wire should be connected to the positive and Black wire to negative.)

 Features:

1.  Iron Body Material
2. High quality ultra-compact electric lock.
3. Rustproof, durable, safe, convenient to use.
4. Suction which tightly sucks the iron, thus locking the door.
5. Applicable for being installed in the escape door or fire door electronic controlled system.
6. Adopts the principle of electric magnetism, when the current through the silicon, the electromagnetic lock will achieve a strong.

QUICK OVERVIEW

1. Holding force: 0.25kg
2. Energized forms: intermittent
3. Unlocking time: 1S
4. Dimensions: 54 x 42 x 28 mm (LxWxH)
5. High quality ultra-compact electric lock.
6. Rustproof, durable, safe, convenient to use.
7. Suction which tightly sucks the iron, thus locking the door.

Applicable for being installed in the escape door or fire door electronic controlled system.

Package Includes:

1 x DC 12V Cabinet Door Lock Electric Lock Assembly Solenoid

Additional Information:

• Production Capacity: 10nos
• Delivery Time: 2 days

Product Details:

QUICK OVERVIEW

1. The metal gears have better wear and tear properties.
2. The gearbox is sealed and lubricated with lithium grease and requires no maintenance.
3. Although motor gives 30 RPM at 12V, the motor runs smoothly from 4V to 12V and gives the wide range of RPM, and torque.
4. The shaft has a hole for better coupling.
5. Operating Voltage(V): 12
6. Rated Torque(kg-cm): 4.2
7. Stall Torque(kg-cm): 16

These motors are simple DC Motors featuring gears for the shaft for obtaining the optimal performance characteristics. They are known as Center Shaft DC Geared Motors because their shaft extends through the center of their gear box assembly.

These standard size DC Motors are very easy to use. Also, you don’t have to spend a lot of money to control motors with an Arduino or compatible board. TheL298N H-bridge module with onboard voltage regulator motor driver can be used with this motor that has a voltage of between 5 and 35V DC.

This DC Motor – 45RPM – 12Volts can be used in all-terrain robots and a variety of robotic applications. These motors have a 3 mm threaded drill hole in the middle of the shaft thus making it simple to connect it to the wheels or any other mechanical assembly.

Nut and threads on the shaft to easily connect and internally threaded shaft for easily connecting it to the wheels.

These DC Geared motors with robust metal/Plastic gearbox for heavy-duty applications, available in the wide RPM range(Check the list below) and ideally suited for robotics and industrial applications.

Note:

Depending upon the Manufacturer given dimensions may vary in the range of ±5%.

We are supplying the range of such Center Shaft DC Motors, you can choose one according to your requirement by clicking on the RPM below

3        –     16 kg-cm
10      –     7 kg-cm
30     –     5 kg-cm
60     –     3.6 kg-cm
100   –     2.9 kg-cm
150    –     2 kg-cm
200   –    1.5 kg-cm
300   –    1.2 kg-cm
500   –    0.7 kg-cm
1000   –    0.5 kg-cm

Features :

1. It comes with Good Quality Gears.
2. The metal gears have better wear and tear properties.
3. The gearbox is sealed and lubricated with lithium grease and requires no maintenance.
4. Although motor gives 45 RPM at 12V, the motor runs smoothly from 4V to 12V and gives the wide range of RPM, and torque.
5. The shaft has a hole for better coupling.

Additional Information:

• Item Code: BE30055

This sketch uses a motor designed to vibrate. If we have an old cell phone we no longer need, it may contain tiny vibration motors that would be suitable.

Vibration motors require more power than an Arduino pin can provide, so a transistor is used to switch the motor current on and off. Any NPN transistor can be used.

A 1 kilohm resistor connects the output pin to the transistor base; the value is not critical, and you can use values up to 4.7 kilohms or so (the resistor prevents too much current flowing through the output pin).

 

We offer good quality LCD module blue ( 16X2 line ) .

Additional Information:

• Item Code: BE20266
• Minimum Order Quantity: 1 Piece

Product Details:

Type c data cable 3.0A Output
Taxko make