Product Details:
Minimum Order Quantity | 1 Piece |
Brand | SCHRACK |
Voltage | 250vac |
Current | 16a |
Relay Type | Voltage Relay |
Product Details:
Usage/Application | Industrial |
Voltage | 12v |
Current | 5a |
Brand | pla |
Type | Industrial Relay |
Product Details:
Minimum Order Quantity | 1 Piece |
Brand | BE |
Usage/Application | Switching |
Number Of Poles | 1 |
Coil Voltage | 12v |
Additional Information:
Product Details:
Minimum Order Quantity | 1 Piece |
Model Name/Number | BE60269 |
Brand | ESP |
ESP8266 WiFi 5V 1 Channel Relay Module equip with ESP8266 WiFi module and micro-controllers, through the mobile phone APP to the module to send serial instructions to achieve in the LAN within the relay for wireless control. This onboard 5V, 10A / 250V AC 10A / 30V DC relay, can be continuous pull 10 million times, with diarrhea flow protection and short response time.
How to use :IN +, IN-: 5V power input;
TX, RX, GND: Serial debug pin;
Onboard the ESP8266 WIFI module has three work modes: STA (client), AP (hot), the STA + Ap( hot +client), according to the workings of a module to the corresponding choice of WIFI module working mode. Module need before use serial debugging software and USB to TTL module send serial command was carried out on the WIFI module configuration (don’t power outages after configuration is complete, as some of the parameters of WIFI module cannot be saved when the power is cut off), mobile phone and WIFI module after establishing a network connection can use the phone APP control relay.
Control Commands :When cell phone equipped with WiFi module sends commands in the following order:
(The default baud rate 115200)
1 x ESP8266 WiFi 5V 1-Channel Relay Module
Additional Information:
A 1,2,4& 8 channel relay module (HCMODU0115) featuring 2x Omron G3MB-202P solid state relays. This 5V 1,2,4& 8 channel SSR G3MB-202P Solid State Relay Module is capable of switching AC voltages between 100 and 240V at up to a 2A current. The module can be controlled from a 5V digital source such as an Arduino microcontroller.
A resistive type fuse is provided on the module to help protect excessive current draw.
This 5V 1,2,4& 8 channel SSR G3MB-202P Solid State Relay Module 240V 2A Output with Resistive Fuse is based on the Omron G3MB SSR relay which can control up to 2A at 240VAC. This is a 2 Channel SSR relay module, each relay channel has 3 separate terminals, NO (Normal Open), COM (Common), NC (Normal Closed).
A Solid State Relay is similar to a mechanic relay where it can be controlled through a digital signal. Solid State Relay generates no noise and has a much longer lifespan in compared to the traditional mechanic relay.
When the input logic voltage is applied to the coil, the NC will disconnect from the COM breaking the conductivity between the two. At the same time, the NO will connect with the COM allowing conductivity between them. Depending on your wiring this will turn on or off the connected load.
Input part :Additional Information:
This is DC To AC SSR-40DA Solid State Relay Module 3-32VDC/24-380VAC 40A. A solid state relay (SSR) allows you to control high-current AC loads from lower voltage DC control circuitry. Solid state relays have several advantages over mechanical relays.
One such advantage is that they can be switched by a much lower voltage and at a much lower current than most mechanical relays. Also, because there are no moving contacts, solid state relays can be switched much faster and for much longer periods without wearing out.
This particular SSR can switch current loads of up to 40A with a 3-32V DC input and a zero cross trigger control method. Each one of these relays is equipped with four screw terminals (for use with ring or fork connectors) and a plastic cover that slides over the top of the relay to protect the terminals.
Additional Information: